Uygulama:* For special inserts of TungCut, please refer to page 6-86.
Açıklama:• Applicable inserts
• Notation of “insert seat size”
• Seat size and grooving width are different. Seat size measure is for
• The specifi cation of the setting insert. Please note this point.
Açıklama:• For diameter compensation values in traversing, see page 6-25.
• For occurrence of vibrations in traversing, set the feed to the lower side of the values show in the above table.
Açıklama:• When ordering, Shank and Blade set are required.
• When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade-set are required.
• When using a right or left hand blade-set, the right hand blade-set is used with right
hand shank and the left hand blade-set is used with left hand shank.
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade-set are required.
• When using a right or left hand blade-set, the right hand blade-set is used with right hand shank and the left hand blade-set is used
with left hand shank.
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade set are required.
• When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used
with left hand shank.
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade-set are required.
• When using a right or left hand blade-set, the right hand blade-set is used with right hand shank and the left hand blade-set is used with left hand shank
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade set are required.
• When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used
with left hand shank.
Açıklama:• For diameter compensation values in traversing, see page 6-37.
• For occurrence of vibrations in face traversing, set the feed to the lower side of
the values show in the above table.
Açıklama:• Special shank of blade for FLEX type.
• When using a right or left hand blade set, the right hand blade set is used with left hand shank and the left hand blade set is used with right hand shank.
• When using a right or left insert, the right hand insert is used with right hand blade set and the left hand insert is used with left hand bladeset.
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade-set are required.
• When using a right or left hand blade-set, the right hand blade-set is used with left hand shank and the left hand blade-set is used with right hand shank.
Açıklama:• When ordering, Shank and blade ass’y Cat. No. or Shank and Blade-set are required.
• When using a right or left hand blade-set, the right hand blade-set is used with left
hand shank and the left hand blade-set is used with right hand shank.
Açıklama:• When using a right or left hand insert, the right hand insert is used with right
hand toolholder and the left hand insert is used with left hand toolholder.
Açıklama:• When depth is deeper than insert length, 1 corner type is recommended.
• “f” value in the above table is calculated with groove width “W” shown in the table.
Açıklama:• External, face grooving and turning (Molded)
• External, internal, face grooving and turning
• Profiling and undercutting (Ground)
• Profiling and undercutting (Molded)
Açıklama:• Notation of “insert seat size”
• Seat size and grooving width are different. Seat size measure is for the specifi cation of the setting insert. Please note this point.
Açıklama:• In DTF and DTX insert types, seat size “6” inserts are not available.
• When 6 size insert is required, the DTE, DGM or
• DGS type is recommended.
Açıklama:Notation of “insert seat size”
Seat size and grooving width are different. Seat size measure is for the specifi cation of the setting insert. Please note this point.
Açıklama:• In DTF and DTX insert types, seat size “6” inserts
are not available. When 6 size insert is required, the
DTE, DGM or DGS type is recommended.
Açıklama:• Notation of “insert seat size”
• Seat size and grooving width are different.
• Seat size measure is for the specifi cation of the setting insert.
• Please note this point.
Açıklama:• Right hand and left hand inserts are effective to minimize burr generation when workpiece is cut off.
• CTK type inserts with positive rake and sharp cutting edge are suitable for parting off and grooving of light alloys and cast irons
Açıklama:• When using a right or left hand insert, the right hand insert is used with right hand toolholder and the left hand insert is used with left hand toolholder.
Açıklama:• When using a right or left hand insert, the right hand insert is used with left hand toolholder and the left hand insert is used with right hand toolholder.
• Max. groove width and max. groove depth shown in the above table are the values when the insert with the largest cutting edge width is used.
Açıklama:• Max. groove width and max. groove depth shown in the above table are the values when the insert with the largest cutting edge width is used.
• When using a right or left hand insert, the right hand insert is used with left hand toolholder and the left hand insert is used with right hand toolholder.
Açıklama:• When using a right or left hand insert, the right hand insert is used with left hand toolholder and the left hand insert is used with right hand toolholder.
Açıklama:• When using a right or left hand insert, the right hand insert is used with right hand toolholder and the left hand insert is used with left hand toolholder.
Açıklama: When using a right or left hand insert, the right hand insert is used with left hand toolholder and the left hand insert is used with right hand toolholder.